Broadcast Qualitylmage The LANO-HSC series comes with a dedicated SP processing chip. with automatic white balance. color correction.Gamma correction. defogging. sharpening and other modules.which can automatically calculate the current colon temperature value and adjust the white balance,and adjust the best color calibration parameters.1080 Phigh-defini tion resolution can realize the maximum restoration of color authenticity in warm and cold tones
Data Storage Management The LANO-HSCseries 64GB and above models alluse self-developed SSD,use Flash array parallel control, optimize the data interface timing to maximize the performance of the storage unit bandwidth.At the same time, you can custom ize the file system to support the recovery of files in case of unexpected power failure during high-speed recording.
The LANO-HSC series is extremelv remodeled in terms of internal circuit board.heat dissipation. structure.et... and adopts mult-layer soft and hard combination board +blind buried hole plate making process to realize the integrated design of PCBA board.The heat flow simulation design is used to optimize the fan structure, and the ultra-thin coaxial cable is used to realize the high-speed connection of each chip board, and the four-layer stack compression is performed at the same time, thereby achieving a volume ratio of over 90%.
| Shooting speed and exposure time | |
| Sensor Type | CMOS |
| Maximum Resolution | 1920x1080 |
| Pixel Size | 10μm |
| ISO | 25000(M),8000(C) |
| Electronic Shutter | Global |
| Minimum exposure time | 100ns |
| PIV Across Frames | 400ns |
| Exposure Function | Automatic Exposure |
| Extreme Dynamic Range | Support |
| Resolution -Frame Rate-Recording Time | ||||||
| Resolution | LANO-HSC200-3003E(measured at 1TB) | LANO-HSC200-2000E(measured at 64GB) | LANO-HSC131-2000E(measured at 16GB) | |||
| Max Frame Rate fps | Recording(s) | Max Frame Rate fps | Recording(s) | Max Frame Rate fps | Recording(s) | |
| 1920×1080 | 3,003 | 173.7 | 2,000 | 15.5 | -- | -- |
| 16472×900 | 3,597 | 226.9 | 2,389 | 20.2 | -- | -- |
| 1280×1024 | 3,164 | 260.7 | 2,109 | 23.2 | 2,000 | 6.5 |
| 1280×960 | 3,378 | 260.4 | 2,252 | 23.2 | 2,132 | 6.5 |
| 1280×800 | 4,048 | 260.8 | 2,702 | 23.2 | 2,557 | 6.5 |
| 1280×768 | 4,219 | 260.6 | 2,808 | 23.2 | 2,666 | 6.5 |
| 1280×720 | 4.504 | 260.3 | 3,003 | 23.2 | 2,840 | 6.5 |
| 832×600 | 5,405 | 400 | 3,597 | 35.7 | 2,412 | 10.0 |
| 640×480 | 6,756 | 519.6 | 4,504 | 46.3 | 4,273 | 13.0 |
| 640×256 | 12,658 | 518.6 | 8,403 | 46.4 | 8.000 | 13.0 |
| 256×128 | 25,000 | 1,281.10 | 16,949 | 112.4 | 15,873 | 32.0 |
| 256×16 | -- | -- | -- | -- | 125,000 | 26.8 |
| 128×16 | 125,000 | 1691.1 | -- | -- | -- | -- |
| Resolution -Frame Rate -Recording Time | |||
| lnterface | Description | Definition | Remarks |
| PWR/LAN | Power and lnterface | 1-8 pin: Connect cable 9 pin: GND 10-15 pin: Internal debugging is not open to the public 16, 17 pin: Negative pole of power supply 18,19 pin: Positive pole of power supply | 1. Power interface, from which the camera is powered; 2.Gigabit network interface, datatransmission betweencamera and PC |
| l/O | lnput, Output | 1,5,7,11,13,17 pin:GND 2,3,4,6 pin:PlV 8pin:TRIG, 9 pin reserve 10,12 pin:SYNC_IN SYNC_oUT 14 pin:lRIG_B 15, 16:RS422 TX_P, TX_N 18, 19 pin:RS422RX_P,RX_N | 1.Trigger interface,5O2 BNC; 2.Synchronous input interface,TTL level interface; 3. Synchronous output interface,TTL level interface; 4.B code interface, DC code, 50QBNC,TTL level; 5.RS422 interface.Communication lnterface. Support protocol customization, such as PTZ, lens, etc.; 6.PiV interface, 4 single-ended BNC,TTL level. |
| SDl | SDl Interface | Power and lnterface | |
| lndicator light | PWR | 1. lt is always on after the external power supply is connected; 2. It detects that the internal temperature of the device is toohigh and enters the flashing state control (5Hz); 3.The device enters breathing state control in standby mode. | |
| OL | 1.The online mode control light is always on; 2.Offline mode control light is flashing (5Hz); 3. ln the offline mode, if it fails to enter the high-speedacquisition, it is always off; 4. In offline mode, the status of data recovery or external triggeracquisition is blinking(1Hz). | ||
| SMP | Highlight flashing, export and export preview breathing lights. | ||
| DISP | Blinks when there is data transmission in the network, and isalways off at other times | ||
| INIT | 1.The breathing state indicates that it is being initialized; 2.The constant light status indicates that the initialization iscomplete; 3.Blinking status indicates initialization failure(5Hz) | ||
English
